#######################################################################
##
## /etc/lighttpd/lighttpd.conf
##
## check /etc/lighttpd/conf.d/*.conf for the configuration of modules.
##
#######################################################################

#######################################################################
##
## Some Variable definition which will make chrooting easier.
##
## if you add a variable here. Add the corresponding variable in the
## chroot example as well.
##
var.log_root    = "/var/log/lighttpd"
var.server_root = "/srv/www"
var.state_dir   = "/run/lighttpd"
var.home_dir    = "/var/lib/lighttpd"
var.conf_dir    = "/etc/lighttpd"

## 
## run the server chrooted.
## 
## This requires root permissions during startup.
##
## If you run chroot'ed, set the variables to directories relative to
## the chroot dir.
##
## example chroot configuration:
## 
#var.log_root    = "/logs"
#var.server_root = "/"
#var.state_dir   = "/run"
#var.home_dir    = "/lib/lighttpd"
#var.vhosts_dir  = "/vhosts"
#var.conf_dir    = "/etc"
#
#server.chroot   = "/srv/www"

##
## Some additional variables to make the configuration easier
##

##
## Base directory for all virtual hosts
##
## used in:
## conf.d/evhost.conf
## conf.d/simple_vhost.conf
## vhosts.d/vhosts.template
##
var.vhosts_dir  = server_root + "/vhosts"

##
## Cache for mod_deflate
##
## used in:
## conf.d/deflate.conf
##
var.cache_dir   = "/var/cache/lighttpd"

##
## Base directory for sockets.
##
## used in:
## conf.d/fastcgi.conf
## conf.d/scgi.conf
##
var.socket_dir  = home_dir + "/sockets"

##
#######################################################################

#######################################################################
##
## Load the modules.
include conf_dir + "/modules.conf"

##
#######################################################################

#######################################################################
##
##  Basic Configuration
## ---------------------
##
server.port = 80

##
## bind to a specific IP
## (default: "*" for all local IPv4 interfaces)
##
#server.bind = "localhost"

##
## Run as a different username/groupname.
## This requires root permissions during startup. 
##
server.username  = "@USER@"
server.groupname = "@GROUP@"

##
## Enable lighttpd to serve requests on sockets received from systemd
## https://www.freedesktop.org/software/systemd/man/systemd.socket.html
##
#server.systemd-socket-activation = "enable"

## 
## enable core files.
##
#server.core-files = "disable"

##
## Document root
##
server.document-root = server_root + "/htdocs"

##
## The value for the "Server:" response field.
##
## It would be nice to keep it at "lighttpd".
##
#server.tag = "lighttpd"

##
## store a pid file
##
server.pid-file = state_dir + "/lighttpd.pid"

##
#######################################################################

#######################################################################
##
##  Logging Options
## ------------------
##
## all logging options can be overwritten per vhost.
##
## Path to the error log file
##
server.errorlog             = log_root + "/error.log"

##
## If you want to log to syslog you have to unset the 
## server.errorlog setting and uncomment the next line.
##
#server.errorlog-use-syslog = "enable"

##
## Access log config
## 
include conf_dir + "/conf.d/access_log.conf"

##
## The debug options are moved into their own file.
## see conf.d/debug.conf for various options for request debugging.
##
include conf_dir + "/conf.d/debug.conf"

##
#######################################################################

#######################################################################
##
##  Tuning/Performance
## --------------------
##
## corresponding documentation:
## https://wiki.lighttpd.net/Docs_Performance
##
## set the event-handler (read the performance section in the manual)
##
## The recommended server.event-handler is chosen by default for each OS.
##
## epoll  (recommended on Linux)
## kqueue (recommended on *BSD and MacOS X)
## solaris-eventports (recommended on Solaris)
## poll   (recommended if none of above are available)
## select (*not* recommended)
##
#server.event-handler = "linux-sysepoll"

##
## The basic network interface for all platforms at the syscalls read()
## and write(). Every modern OS provides its own syscall to help network
## servers transfer files as fast as possible 
##
#server.network-backend = "sendfile"

##
## As lighttpd is a single-threaded server, its main resource limit is
## the number of file descriptors, which is set to 1024 by default (on
## most systems).
##
## If you are running a high-traffic site you might want to increase this
## limit by setting server.max-fds.
##
## Changing this setting requires root permissions on startup. see
## server.username/server.groupname.
##
## By default lighttpd would not change the operation system default.
## But setting it to 16384 is a better default for busy servers.
##
## With SELinux enabled, this is denied by default and needs to be allowed
## by running the following once: setsebool -P httpd_setrlimit on
##
server.max-fds = 16384

##
## listen-backlog is the size of the listen() backlog queue requested when
## the lighttpd server ask the kernel to listen() on the provided network
## address.  Clients attempting to connect() to the server enter the listen()
## backlog queue and wait for the lighttpd server to accept() the connection.
##
## The out-of-box default on many operating systems is 128 and is identified
## as SOMAXCONN.  This can be tuned on many operating systems.  (On Linux,
## cat /proc/sys/net/core/somaxconn)  Requesting a size larger than operating
## system limit will be silently reduced to the limit by the operating system.
##
## When there are too many connection attempts waiting for the server to
## accept() new connections, the listen backlog queue fills and the kernel
## rejects additional connection attempts.  This can be useful as an
## indication to an upstream load balancer that the server is busy, and
## possibly overloaded.  In that case, configure a smaller limit for
## server.listen-backlog.  On the other hand, configure a larger limit to be
## able to handle bursts of new connections, but only do so up to an amount
## that the server can keep up with responding in a reasonable amount of
## time.  Otherwise, clients may abandon the connection attempts and the
## server will waste resources servicing abandoned connections.
##
## It is best to leave this setting at its default unless you have modelled
## your traffic and tested that changing this benefits your traffic patterns.
##
## Default: 1024
##
#server.listen-backlog = 128

##
## Stat() call caching.
##
## lighttpd can utilize FAM/Gamin to cache stat call.
##
## possible values are:
## disable, simple, inotify, kqueue, or fam.
##
#server.stat-cache-engine = "simple"

##
## Fine tuning for the request handling
##
## max-connections == max-fds/3)
## (other file handles are used for fastcgi/files)
##
#server.max-connections = 1024

##
## How many seconds to keep a keep-alive connection open,
## until we consider it idle. 
##
## Default: 5
##
#server.max-keep-alive-idle = 5

##
## How many keep-alive requests until closing the connection.
##
## Default: 16
##
#server.max-keep-alive-requests = 16

##
## Maximum size of a request in kilobytes.
## By default it is unlimited (0).
##
## Uploads to your server cant be larger than this value.
##
#server.max-request-size = 0

##
## Time to read from a socket before we consider it idle.
##
## Default: 60
##
#server.max-read-idle = 60

##
## Time to write to a socket before we consider it idle.
##
## Default: 360
##
#server.max-write-idle = 360

##
##  Traffic Shaping 
## -----------------
##
## see /usr/share/doc/lighttpd/traffic-shaping.txt
##
## Values are in kilobyte per second.
##
## Keep in mind that a limit below 32kB/s might actually limit the
## traffic to 32kB/s. This is caused by the size of the TCP send
## buffer. 
##
## per server:
##
#server.kbytes-per-second = 128

##
## per connection:
##
#connection.kbytes-per-second = 32

##
#######################################################################

#######################################################################
##
##  Filename/File handling
## ------------------------

##
## files to check for if .../ is requested
## index-file.names            = ( "index.php", "index.rb", "index.html",
##                                 "index.htm", "default.htm" )
##
index-file.names += (
  "index.xhtml", "index.html", "index.htm", "default.htm", "index.php"
)

##
## deny access the file-extensions
##
## ~    is for backupfiles from vi, emacs, joe, ...
## .inc is often used for code includes which should in general not be part
##      of the document-root
url.access-deny             = ( "~", ".inc" )

##
## disable range requests for pdf files
## workaround for a bug in the Acrobat Reader plugin.
## (ancient; should no longer be needed)
##
#$HTTP["url"] =~ "\.pdf$" {
#  server.range-requests = "disable"
#}

##
## url handling modules (rewrite, redirect)
##
#url.rewrite                = ( "^/$"             => "/server-status" )
#url.redirect               = ( "^/wishlist/(.+)" => "http://www.example.com/$1" )

##
## both rewrite/redirect support back reference to regex conditional using %n
##
#$HTTP["host"] =~ "^www\.(.*)" {
#  url.redirect            = ( "^/(.*)" => "http://%1/$1" )
#}

##
## which extensions should not be handle via static-file transfer
##
## .php, .pl, .fcgi are most often handled by mod_fastcgi or mod_cgi
##
static-file.exclude-extensions = ( ".php", ".pl", ".fcgi", ".scgi" )

##
## error-handler for all status 400-599
##
#server.error-handler       = "/error-handler.html"
#server.error-handler       = "/error-handler.php"

##
## error-handler for status 404
##
#server.error-handler-404   = "/error-handler.html"
#server.error-handler-404   = "/error-handler.php"

##
## Format: <errorfile-prefix><status-code>.html
## -> ..../status-404.html for 'File not found'
##
#server.errorfile-prefix    = server_root + "/htdocs/errors/status-"

##
## mimetype mapping
##
include conf_dir + "/conf.d/mime.conf"

##
## directory listing configuration
##
include conf_dir + "/conf.d/dirlisting.conf"

##
## Should lighttpd follow symlinks?
## default: "enable"
#server.follow-symlink = "enable"

##
## force all filenames to be lowercase?
##
#server.force-lowercase-filenames = "disable"

##
## defaults to /var/tmp as we assume it is a local harddisk
## default: "/var/tmp"
#server.upload-dirs = ( "/var/tmp" )

##
#######################################################################

#######################################################################
##
##  SSL Support
## ------------- 
##
## https://wiki.lighttpd.net/Docs_SSL
#
## To enable SSL for the whole server you have to provide a valid
## certificate and have to enable the SSL engine.::
##
##   server.modules += ( "mod_openssl" )
##
##   ssl.privkey = "/path/to/privkey.pem"
##   ssl.pemfile = "/path/to/fullchain.pem"
##   # ssl.pemfile should contain the sorted certificate chain, including
##   # intermediate certificates, as provided by the certificate issuer.
##   # If both privkey and cert are in same file, specify only ssl.pemfile.
##
##   # Check your cipher list with: openssl ciphers -v '...'
##   # (use single quotes with: openssl ciphers -v '...'
##   #  as your shell won't like ! in double quotes)
##   #ssl.cipher-list            = "HIGH"   # default
##
##   # (recommended to accept only TLSv1.2 and TLSv1.3)
##   #ssl.openssl.ssl-conf-cmd = ("MinProtocol" => "TLSv1.2")  # default
##
##   $SERVER["socket"] == "*:443" {
##     ssl.engine  = "enable"
##   }
##   $SERVER["socket"] == "[::]:443" {
##     ssl.engine  = "enable"
##   }
##
#######################################################################

#######################################################################
##
## custom includes like vhosts.
##
#include conf_dir + "/conf.d/config.conf"
#include conf_dir + "/vhosts.d/*.conf"
##
#######################################################################
